Loading... Please wait...

InvenSense ITG-3050 Integrated 3-Axis Digital Output Gyroscope Sensor IC

Hover over image to zoom

  • Image 1
InvenSense
€2.83
SKU:
ITG-3050
Availability:
Contact sales@glyn.com.au for delivery leadtime if quantity to be ordered is greater than our stock
Shipping:
Calculated at checkout
Current Stock:
775

 Product Description

The ITG-3050 is a single-chip, digital output, 3-Axis MEMS gyro IC which features a 512-byte FIFO and a secondary I²C sensor bus that interfaces to 3rd party digital accelerometers. The combination of FIFO and dedicated sensor bus allows the ITG-3050 to directly acquire data from an off-chip accelerometer without intervention from an external processor. This both lowers the traffic on the primary (application processor) bus interface and saves power by allowing the system processor to burst read sensor data from the ITG-3050’s FIFO and then go into a low-power sleep mode while the device collects more data.

The ITG-3050 gives users a direct upgrade path to InvenSense’s MPU and IMU family of products by connecting the 3rd party accelerometer to the ITG-3050’s secondary I²C Bus. The ITG-3050 is pin to pin compatible with the MPU and IMU family of products, which allow integration with InvenSense’s software solutions.

The ITG-3050 features a 3-axis digital gyro with programmable full-scale ranges of ±250, ±500, ±1000, and ±2000 degrees/sec (dps or °/sec), which is useful for precision tracking of both fast and slow motions. Rate noise performance sets the industry standard at 0.01 dps/√Hz, providing the highest-quality user experience in pointing, gaming, user interface, and other motion-based applications. Factory-calibrated initial sensitivity reduces production-line calibration requirements.

Other industry-leading features include on-chip 16-bit ADCs, programmable digital filters, a precision clock with 1% drift from -40°C to 85°C, an embedded temperature sensor, programmable interrupts, and a low 5.9mA supply current. The ITG-3050 comes with an I²C serial interface, a VDD operating range of 2.1 to 3.6V, and a VLOGIC interface voltage from 1.71V to 3.6V.

By leveraging its patented and volume-proven Nasiri-Fabrication platform, which integrates MEMS wafers with companion CMOS electronics through wafer-level bonding, InvenSense has driven the ITG-3050 package size down to a revolutionary footprint of 4x4x0.9mm (QFN), while providing the highest performance, lowest noise, and the lowest cost semiconductor packaging to address a wide range of handheld consumer electronic devices. The device provides the highest robustness by supporting 10,000g shock in operation. The highest cross-axis isolation is achieved by design from its single silicon integration.

Features

  • X-, Y-, Z-Axis angular rate sensors (gyros) on one integrated circuit
  • Angular rate sensors (gyros) with user-programmable full-scale-range of ±250°/sec, ±500°/sec, ±1000°/sec, or ±2000°/sec.
  • 16-bit ADCs for digitizing sensor outputs
  • Programmable low-pass filters
  • When used together with a 3rd-party digital 3-axis accelerometer, the ITG-3050 collects the accelerometer data via a dedicated sensor interface, while synchronizing data sampling at a user defined rate. The total data set obtained by the ITG-3050 includes 3-axis gyroscope data, 3-axis accelerometer data, temperature data, and the one bit external sync signal connected to the FSYNC pin. The ITG-3050 also downloads the results calculated by the digital 3-axis 3rd party accelerometer internal registers.
  • FIFO buffers complete data set, reducing timing requirements on the system processor and saving power by letting the processor burst read the FIFO data, and then go into a low-power sleep mode while the ITG-3050 collects more data.
  • VDD supply voltage range of 2.1V to 3.6V
  • Flexible VLOGIC reference voltage allows for multiple I²C interface voltage levels
  • Power consumption with all three axis active: 5.9mA
  • Sleep mode: 5μA
  • Each axis can be individually powered down
  • Small 4x4x0.9mm QFN package
  • MEMS structure hermetically sealed and bonded at wafer level
  • RoHS and Green compliant

Applications

  • Motion-enabled game controllers
  • Handheld gaming
  • Handset User Interface
  • Motion-based Digital TV and Set Top Box remote controls
  • Location based services, points of interest, and dead reckoning
  • Improved camera image quality through image stabilization
  • Health and sports monitoring

ITG-3050 Block Diagram

itg-3050-block-diagram-600.jpg

Documentations

 Find Similar Products by Tag

gyro  gyroscope  MEMS  motion  sensor  tracking  

 Find Similar Products by Category

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

 

newsletter

Copyright 2017 Glyn Store. All Rights Reserved.
Sitemap | BigCommerce Premium Themes by PSDCenter

Click the button below to add the InvenSense ITG-3050 Integrated 3-Axis Digital Output Gyroscope Sensor IC to your wish list.